Floor and walls completely flat and level. Water points should be good have been flushed so that there is no grit and dirt in the pipes. This is possible causing malfunctions that are not covered by the warranty. Space must be easily accessible. Water and electricity are required at the connection points be present to test the Upfall Shower. Do not use pressure boosters!
Keep to the locations of the connection points. • Hot water supply between 55 and 60 degrees • Placing valves on the wall (eg Ballofix) • Flush pipes before connecting • No water should remain in the drain (test before tapering off!) • Drain at least 8% Pay attention! |

DRAIN
PVC sleeve 40mm, top edge of the
sleeve on floor level.
Remember, let drain 8% efflux.
PVC sleeve 40mm, top edge of the
sleeve on floor level.
Remember, let drain 8% efflux.

WATER
Check the water temperature. This must be between 55 and 60 Celsius
A 15 cm wall plate for hot and cold water
150 cm from the floor. Place two shut-off valves outside thread pointed downwards . Heart 45 cm from the corner or center behind the panel.
ELECTRICAL
Junction box, earthed 220 volt at 175 cm height
the floor. Consumption system 150 watts. Fuse 30 mA
Check the water temperature. This must be between 55 and 60 Celsius
A 15 cm wall plate for hot and cold water
150 cm from the floor. Place two shut-off valves outside thread pointed downwards . Heart 45 cm from the corner or center behind the panel.
ELECTRICAL
Junction box, earthed 220 volt at 175 cm height
the floor. Consumption system 150 watts. Fuse 30 mA

The frame height can be shortened!
Drain 70x10 cm. Pre-assembled on the frame.

Installation depth drain to bottom of tiles 9 cm.
Frame depth to wall at least 20 cm.

Click here to edit.
Mounting Excellent Drain
Easy to do, plug & play

1. Thoroughly flush the water pipes that come out of the wall
before connecting the water supply to the panel.
Dirt and construction grit from pipes can cause malfunctions
(these malfunctions are not covered by the warranty).
2. Connect the water with the supplied reinforced hoses.
These are labeled blue for cold water and red for warm water.
3. Also connect the electricity.
caution!
Make sure that all parts behind the frame are not in contact with the wall!
Connect hot and cold water well! The pipes are
labeled.
before connecting the water supply to the panel.
Dirt and construction grit from pipes can cause malfunctions
(these malfunctions are not covered by the warranty).
2. Connect the water with the supplied reinforced hoses.
These are labeled blue for cold water and red for warm water.
3. Also connect the electricity.
caution!
Make sure that all parts behind the frame are not in contact with the wall!
Connect hot and cold water well! The pipes are
labeled.

Now attach the frame to the wall. Pay attention! During adjustment the technical components must not touch the rear wall and the pump must not come into contact with the wall.

Fix the legs of the frame to the floor.

Fix the legs of the frame to the floor.

Important!
Test the system for proper drainage of the drain. Use
for example a bucket with water or use the supplied
hand shower. Wait for the drain to drain completely.
If not, the frame will be placed slightly higher
with respect to the drain, so that it drains well.
Test the system for proper drainage of the drain. Use
for example a bucket with water or use the supplied
hand shower. Wait for the drain to drain completely.
If not, the frame will be placed slightly higher
with respect to the drain, so that it drains well.

Make a wooden formwork around the Upfall Shower floor drain.
So that the technology behind the drain remains accessible at all times. If this is not the case, the warranty will lapse in the event of any
malfunctions.
So that the technology behind the drain remains accessible at all times. If this is not the case, the warranty will lapse in the event of any
malfunctions.

You can isolate the drain very well by packing it with
insulation material, this will ensure that your Upfallshower still
is more economical. Good insulation ensures less hot water use.
Pour the screed to the edge of the drain, take into account
with the thickness of tiles. Make sure the waterproof bib fits properly on the screed.
Think about the drain to the sewer of at least 1 cm
per meter! Xenz is not responsible for functioning
of the system if the floor is not sloping enough.
insulation material, this will ensure that your Upfallshower still
is more economical. Good insulation ensures less hot water use.
Pour the screed to the edge of the drain, take into account
with the thickness of tiles. Make sure the waterproof bib fits properly on the screed.
Think about the drain to the sewer of at least 1 cm
per meter! Xenz is not responsible for functioning
of the system if the floor is not sloping enough.

The carpentry of the frame can be done with waterproof
sheet material.
When choosing the finishing material, consider the
thickness of tile relative to the finishing frame around the glass plate and the space between frame and drain (25mm).
sheet material.
When choosing the finishing material, consider the
thickness of tile relative to the finishing frame around the glass plate and the space between frame and drain (25mm).

You can make the connection of the shower arm disappear into the tiles.
The chrome sealing ring can be slid over it later.
Seal well.
The chrome sealing ring can be slid over it later.
Seal well.

When tiling, take into account a joint around the
floor drain.
Seal it after tiling.
floor drain.
Seal it after tiling.

If you do not have a black or white cover for the drain,
you can cover the supplied stainless steel tile panel with your tiles.
you can cover the supplied stainless steel tile panel with your tiles.
Clean the drain well before use. Make sure the drain can drain completely,
no water should remain in the drain. Defects in the system due to incorrect
mounting is not covered by warranty.
no water should remain in the drain. Defects in the system due to incorrect
mounting is not covered by warranty.